=== Please Select === 12 (std 12" x 28") 20 (std 14" x 33") 30 (std 16" x 38") 60 (std 20" x 48") 80 (std 24" x 47") 120 (std 30" x 46") 200 (std 30" x 74") 240 (std 30" x 84") 400 (std 36" x 92") 500 (std 36" x 116") 620 (std 42" x 113") 1040 (std 48" x 144") 1550 (std 54" x 168") 2200 (std 60" x 192") 3000 (std 66" x 217") 3750 (std 72" x 230") 5000 (std 72" x 305") 7500 (std 84" x 340") 10000 (std 96" x 350") 15000 (std 96" x 499") 20000 (std 120" x 429") 30000 (std 120" x 635") Other (please fill in blank below)
(Other)

• Quick Note About Capacity:
  • Dimensions listed behind each capacity give standard tank diameter and tank overall length (including straight side and elliptical heads but not including base rings, legs, flange stick out, etc). If you need a non-standard size, please define your dimensional requirements in the “Comments/Special Requirements” section below. (For example: Due to ceiling ht, vessel cannot exceed 10 ft)
     
• Quick Tip About Capacity:
  • Especially for air receivers 80 gallons or larger, when considering the size of the air receiver for your installation site, it is suggested to allow 12” on all sides of the standard diameter and tank length dimensions listed to account for base rings, legs, flange stick-out and give consideration to ceiling heights, door widths, angular clearance for tipping vertical receivers into location, etc. Air receivers smaller than 80 gallons should consider 6” clearance all on sides.
    

• Quick Note About Max Rated Design Pressure:
  • Keep in mind that as a minimum the max design pressure of the air receiver should exceed maximum anticipated operating pressure by at least 10% to reduce the likelihood of the safety relief device (not included) releasing during normal operation. If you need a vacuum rated vessel, please indicate this in the Comments/Special Requirements section.
    

=== Please Select === Std red oxide primer (standard for most carbon receivers) Std Industrial Enamel (Med. Gray) Std Industrial Enamel (Black) Std Industrial Enamel (White) Std Industrial Enamel (Blue) Std Industrial Enamel (Yellow) Std Industrial Enamel (Green) Std Epoxy (Lt. Gray 3 mil DFT) Std Galvanize (shipped from galvanizer / also includes interior) Premium Galvanizing (Cleaned at Silvan / also includes interior) No special finish, as fabricated (stainless steel vessel) Blasted matte finish (stainless steel vessels only) Other (please fill in blank below)
(Other)

=== Please Select === Bare, no finish required (standard for most receivers) Std Epoxy (Lt. Gray 3 mil DFT) Std Galvanizing (shipped from galvanizer / also includes exterior) Premium Galvanizing (cleaned as accessible at Silvan / also includes exterior) Other (please fill in blank below)
(Other)

Please list any specialized requirements you have in the section provided below. The accuracy of our quotation relies on the amount of information you provide if special requirements are needed for your project. Click below to view our standard design features:

• Standard air receiver design features include:
  • Typical temperature rating is -20F to 450F.
  • Inlet/Outlet and misc NPT will be based on Silvan "stock tank" designs of same approximate capacity. Please list inlet and outlet size below if known.
  • Vessels over 36" diameter will have a 12" x 16" manway in the sidewall.
  • Vessel will be ASME certified. Additional fees apply for CRN, ABS, USCG, CE, etc.
  • Vessels will not have special consideration for additional corrosion allowance, wind load, vacuum, earthquake, etc.
  • When ordered, Silvan will provide one copy of the final assembly drawing and once completed, a copy of the ASME U1-A certificate.

Comments / Special Requirements: